Plans will be displayed here, updated.
also have index of my boat material supplier websites at bottom of page
Full Boat Plans: Main drawing I am working on. All others will be pulled from here.
| full_boat_plans.jpg |
| full_boat_plans.tcw |
Bow Bottom Dimensions
| bow_bottom_dimensions.jpg |
| bow_bottom_dimensions.tcw |
Here are the BOW SIDE DIMENSIONS. Going to place gussets on either side of the side frame members and the bottom frame members. This will make where you only have to set the saws angle once per frame.
Added gusset on the top of the frame to help align nose form.
Added gusset on the top of the frame to help align nose form.
| bow_side_dimensions.jpg |
| bow_side_dimensions.tcw |
| nose_form.jpg |
| nose_form.tcw |
Frame 1 Dimensions
| frames_1_dimensions.jpg |
| frames_1_dimensions.tcw |
Frame 2: I will not notch the side frames, since it will be difficult to slope the notches, and just mark where they will be glued on the sides. Also going to mark where nose form butts up again top frame member, which will be alighed with gussets as well.
| frames_2_dimensions.jpg |
| frames_2_dimensions.tcw |
Frame 3 Dimensions: We lose the bottom side chine due to the hull bottom sloping up at this point, but since sides do not bend in yet, we still have same number of battens on bottom.
| frames_3_dimensions.jpg |
| frames_3_dimensions.tcw |
Frames 4 - 8 Dimensions
| frames_4-8_dimensions.jpg |
| frames_4-8_dimensions.tcw |
Here are the Aft Dimensions
| aft_dimensions.jpg |
| aft_dimensions.tcw |
Frame 9 is a three parter. Here is Part A.
| frame_9a_dimensions.jpg |
| frame_9a_dimensions.tcw |
Here are dimensions for both Part B and Part C of Frame 9.
| frame_9b_dimensions.jpg |
| frame_9b_dimensions.tcw |
Frames 10 & 11, as well as the inner brace, end piece and the sub deck. I plan using the sub deck to help form and keep the frames aligned.
| frames_10__11_dimensions.jpg |
| frames_10__11_dimensions.tcw |
AFT INNER SIDE FORM made from 1/2" Marine Grade Plywood
| aft_inner_side_form.tcw |
| aft_inner_side_form.jpg |
RUDDER SUPPORT AND KEEL made from 2"x8".
| rudder_support_and_keel.tcw |
| rudder_support_and_keel.jpg |
RUDDER made from laminated 2"x8".
| rudder.jpg |
| rudder.tcw |
PADDLE WHEEL SUPPORT
| wheel_support.jpg |
| boat_3_wheel_support.tcw |
PADDLE WHEEL :circles made from 1/2" Marine Grade Plywood, spokes from 1"x 3" poplar
and paddles from 1"x8" poplar.
and paddles from 1"x8" poplar.
| wheel.tcw |
| wheel.jpg |
SIDE VIEW WITH FRAME AND CHINES SPACINGS
| fames_and_chines.jpg |
| fames_and_chines.tcw |
Great Sites for parts:
Glen-L boat building supplier
http://www.boatdesigns.com/Boatbuilding-Supplies-Hardware/departments/3/
for resin, slow hardener, and fiber cloth (both 10oz for hull, and 4 oz for deck which is transparent and shows the wood beautfully.) They also sell plans for other boats.
MCmaster-Carr
http://www.mcmaster.com/
for #40 chain, gears, bearings, shafts and flanges to attach paddle wheel to shatf.
Go 2 Marine
http://www.go2marine.com/
for lights and running gear.
V-Belts
http://www.vbeltsupply.com/
for great place to get belt of all kinds and sizes.
Glen-L boat building supplier
http://www.boatdesigns.com/Boatbuilding-Supplies-Hardware/departments/3/
for resin, slow hardener, and fiber cloth (both 10oz for hull, and 4 oz for deck which is transparent and shows the wood beautfully.) They also sell plans for other boats.
MCmaster-Carr
http://www.mcmaster.com/
for #40 chain, gears, bearings, shafts and flanges to attach paddle wheel to shatf.
Go 2 Marine
http://www.go2marine.com/
for lights and running gear.
V-Belts
http://www.vbeltsupply.com/
for great place to get belt of all kinds and sizes.
