Paddle Wheel Boat
  • Current Progress
  • Third Boat Build
    • Designing new boat
    • Building Frame Support
    • Building the Frames
    • Building the Hull >
      • Hull Part 2
      • Hull Part 3
    • Building the Paddle Wheel
    • Building the Decks and Canopy
    • Hooking up Rudder and Propulsion >
      • Propulsion Part 2
    • Building the Cabin
    • First Time out
    • New Angled Tansom
    • Larger Engine Required
    • Better Steering
    • Water Shield
    • Torque - The missing element
    • Plans
  • Boat 3 Reconstruction
    • Hoisting the Boat
    • Cutting Aft Off
    • New Pontoons
    • Getting an Engine
    • Transmission and cooling system
    • Side projects keep pulling me away
    • New pontoons (a redo)
  • Second Boat Built
    • Build Slideshow
    • A Few Tweaks and Redesigning
    • Redesigned boat
    • 1. Building the HULL
    • 2. Building Propulsion system
    • 3. Building the Cabin
    • 4. Building the Second Deck
    • SUPPLIMENTAL BOAT PLANS
    • CLASS 1 BOATS and WHAT is REQUIRED
  • First Boat Built
    • Photos of FIrst Boat Build
  • MY TEAM
  • OTHER PROJECTS
    • The Boat Trailer
    • Ark of Covenant Baptistry
    • Motorcycle Rocker
    • Side Wheel Paddle Boat : project is currently suspended
    • Papercraft Hobbies
    • Cross-Stitching Photos
  • Current Progress
  • Third Boat Build
    • Designing new boat
    • Building Frame Support
    • Building the Frames
    • Building the Hull >
      • Hull Part 2
      • Hull Part 3
    • Building the Paddle Wheel
    • Building the Decks and Canopy
    • Hooking up Rudder and Propulsion >
      • Propulsion Part 2
    • Building the Cabin
    • First Time out
    • New Angled Tansom
    • Larger Engine Required
    • Better Steering
    • Water Shield
    • Torque - The missing element
    • Plans
  • Boat 3 Reconstruction
    • Hoisting the Boat
    • Cutting Aft Off
    • New Pontoons
    • Getting an Engine
    • Transmission and cooling system
    • Side projects keep pulling me away
    • New pontoons (a redo)
  • Second Boat Built
    • Build Slideshow
    • A Few Tweaks and Redesigning
    • Redesigned boat
    • 1. Building the HULL
    • 2. Building Propulsion system
    • 3. Building the Cabin
    • 4. Building the Second Deck
    • SUPPLIMENTAL BOAT PLANS
    • CLASS 1 BOATS and WHAT is REQUIRED
  • First Boat Built
    • Photos of FIrst Boat Build
  • MY TEAM
  • OTHER PROJECTS
    • The Boat Trailer
    • Ark of Covenant Baptistry
    • Motorcycle Rocker
    • Side Wheel Paddle Boat : project is currently suspended
    • Papercraft Hobbies
    • Cross-Stitching Photos
Paddle Wheel Boat

Having to put the boat build on hold till after our family reunion. It is at our house this year and we need the extra parking space. This gives me time to figure out how I want to construct the building frame that I will build the boat on.
Just updated plans section and added listing of my favorite boat supplier sites at bottom Plans page.
I placed some pictures with dimensions for the new boat parts under the Plans section of the Present Build, along with both of the jpeg and autocad files.
Picture
Alright. Just finished the Nose Form diagrams, which completes the foward half of the hull. Soon as I do frames 9, 10 & 11, I will be ready to begin contrustion.

Picture
Here are the angle for the Aft end.

Picture
Here are Frame 9's dimensions. There are 3 main parts: part A is the outter plywood sheet, part B is made of 2"x6"s glued to part A, and part C is just a 2"x6" glued to the bottom of part B to form a lip for the deck.

Picture
OK. Last frames done. Plan to begin building the stand that will hold the build.

Picture
I'm all excited again. Decided to redesign the rear wheel paddle boat. Here are my rough drawings. Placing rudder back in the middle, which uncomplicates the twin rear rudder. Still going to have rudder in rear, but extending below hull a bit. Seen sailboat plans and copied them. Now that I am redesigning to fit equipment I have, I can have the gas tank, engine and battery all lined up at the rear. This will place the engine in the center for best weight support. I may also center the gas tank, and may move it up foward. Not sure where I want to steer the boat from, and may build boat and then decide. No extending upper deck, which will place wieght where it belongs, below the water line. Will have 8' interior deck space, which will give us a nice area to place benches and such. 

Picture
Here is the boat design in autocad. It was not until I was making the autocad version of the boat, that I discovered I had inadvertanly left out the number 11 in calculating the length of my boat.

Picture
Picture
Here is a rough Idea of the new boat design. I removed 8 paddles due to the distance between them. The 6' paddle wheel had a spacing of 18" and the 4" wheel would have had about 6" spacing. But removing 8 paddles restored the spacing to 18". 

Picture
Here are the messurements for frames 4 -8. The chines are set within notches, while I have the battens simply attached to the bottom to allow water flow. I also added gassets to ensure the sides of the hull are 90 degrees.

Picture
Here are the BOW SIDE DIMENSIONS. Going to place gussets on either side of the side frame members and the bottom frame members. This will make where you only have to set the saws angle once per frame.

Picture
Bow Bottom Dimensions: Displayed are also the gussets to align the nose form.

Picture
Just added Frame 1-3 to Plans page. Notice notches for nose form supports. Nose for will have two beams to support it stretching all the way to frame 2.Will have hexagon shape gussets to help align the nose.

Picture
Alright. Just finished the Nose Form diagrams, which completes the foward half of the hull. Soon as I do frames 9, 10 & 11, I will be ready to begin contrustion.

    If have questions or comments, feel free to send them in. 

Submit
Proudly powered by Weebly